COMMANDER44 ECU SOFTWARE

Here is the simple and secure method of update of your ECU with a new software version.

Documentation dowload


 

Download Cmd44_ENU-4.2.0.0.zip

WARNING LEVEL : IMPORTANT

 

Graphical display

 


 

NEW FEATURES AND IMPROVEMENTS

Significant improvement of the engine startup security:
• In the previous versions, during difficult conditions of engine start-up, the microprocessor could lose the capacity to perform its measurements (throttle, pressures, temperatures, ...), causing an engine stalling.
• This version prevents the loss of the measurements even in case of battery tension drop down at the engine start.

Very efficient improvement of the launch procedure by a sliding of the launch limiter toward the race limiter:
To avoid the skating at the vehicle take-off, rather than going up suddenty from the launch to the race limiter, the rpm limiter is gradually raised from the launch limiter to the race limiter, at the maximum speed at which you allow the engine to rev up (tunable) - see new limiter documentation.

New calibration of the Auxiliary CAN-Bus for new Dashboards (V410):
• A new "Extension" type allows to directly inform the new Dashboards type, like RgCartronic, Gems, Motec, ..., and the data recordings devices. With this new type, almost all the measurements and calculation results of the ECU are automatically sent by the Auxiliary CAN-Bus in a simple way.
• This is in addition to the old "Injall" type which allows to directly inform the AIM type Dashboards.

Sequential gearbox (V410):
• Improvement of the calculation security of the ignition advance modification while gear upshifting: maps of advance modification are not used if "Ignition adavance modification" box is not checked. Whatever is their value, they do not change the ignition advance behavior.

Improvement of quality and robustness of the injection command (V400):
• When engine speed instabilities of a sufficient level (due to vibrations or else) happened, versions previous to version 400 may lose one or more injections, up to making thinking to a small limiter.
• The new versions never lose any injection (nor ignition) whichever is the engine operation.

 

CONTENT

Commander44 Tunewares:
• System V520
• Throttle/RPM: V420 (new - 26th 11/2016)
• Pressure/RPM and turbo: V420 (new - 26th 11/2016)
• Archives of all the former Tunewares to open the not yet updated machines of this type

Documentations in English:
• Commander44 tuning software pack: 35 separate documents, each for one specific fonction of the ECU, with many didactic examples (new - 26th 11/2016)
• Commander44 installation: V1.42 - with commands of ignition modules (23rd 06/2015)
• Commander44 options installation: V1.20 - sequential gearboxes, fly by wire, air electrovalves, bang-bang, ... (26th 10/2015)

Nota:
• Does not contain Winjall software. Winjall must first be downloaded and installed apart.
• Does not contain the sensors convertion maps nor the actuators command maps. These maps have to be downloaded and installed apart with the pack SensAct.

 

LAST SECURITY CRITICAL MODIFICATION DONE

Since system version V300, improvement of machine internal security.
Particularly when tuning, updating and bolting ECUs.
No parasite software or data can be inserted

 

Button to launch the downloads

 

NEEDING Winjall V9.0.0.0 (see specific downloading)

V9.0.0.0 or later version of Winjall software must mandatory have been installed first.

 

HOW TO UPGRADE TUNEWARES

• Download new .zip Commander44 software pack file and save it in a directory on your hard disk.
• If you have already install a former version of this pack, you have to usinstall it before installing this new one:
In Windows XP, execute 'Start/Parameters/Configuration/Add-Remove programs'.
In Windows 7 and latter versions, execute 'Start/Parameters/Configuration/Programs and features'.
In the software list, select Commander44 then 'Uninstall'. Follow uninstall instructions.
• With the explorer, double click on the downloaded software pack .zip file, then double click on Setup. At the question on files extraction, answer 'Extract All'.
• If the installation does not automatically start: in the new directory created by the extraction, double click on Setup (application).

 

 


 

VERSIONS HISTORY
(Improvements are added from a version to the next one)

 

Throttle/RPM : V410 (System V510)
Pressure/RPM : V410 (System V510)

1) New calibration of the Auxiliary CAN-Bus for new Dashboards:
- A new "Extension" type allows to directly inform the new Dashboards type, like RgCartronic, Gems, Motec, ..., and the data recordings devices. With this new type, almost all the measurements and calculation results of the ECU are automatically sent by the Auxiliary CAN-Bus in a simple way.
- This is in addition to the old "Injall" type which allows to directly inform the AIM type Dashboards.
2) Sequential gearbox
- Improvement of the calculation security of the ignition advance modification while gear upshifting: maps of advance modification are not used if "Ignition adavance modification" box is not checked. Whatever is their value, they do not change the ignition advance behavior.

 

Throttle/RPM : V400 (System V500)
Pressure/RPM : V400 (System V500)

1) Improvement of quality and robustness of the injection command:
- When engine speed instabilities of a sufficient level (due to vibrations or else) happened, the previous versions may lose one or more injections, up to making thinking to a small limiter.
- This new version never loses any injection (nor ignition) whichever is the engine operation.

 

Throttle/RPM : V370 (System V460)
Pressure/RPM : V370 (System V460)

1) Use of wide band Labda sensors:
- Improvement of the reliability of the injection time self learning at high richness.
- Better detection of Lambda sensor failure.
2) Sequential gearbox
- Automatic boost (autoblip) by the mean of the motorized throttle on gear downshift (needs an analogical powershift switch allowing to detect the downshifting, like strain gauge switches).
- Removal of interventions on injection time on gear upshift - quite never used - (only remains interventions on ignition, used by the whole of the motorists).
- Permission for the user to make the calibration of the gear position potentiometer and of the detection thresholds of the analogical powershift switch, even when the ECU has been locked by a professionnal license.

 

Throttle/RPM : V360 (System V450)
Pressure/RPM : V360 (System V450)

1) Direct injection:
Modification of injection pressure calculation for gasoline direct injection.
Gives a better adaptation of the injection times to the fuel pressure.
2) Richness correction:
Significant acceleration of richness correction recovery on re-synchronization on exit of rpm sensor signal loss.

 

Throttle/RPM : V350 (System V450)
Pressure/RPM : V350 (System V450)

1) Sequential gearbox:
More and more gearboxes are equipped with a strain gauge switch, and no more with a On-Off switch.
This version makes much more easier the tuning of this kind of switches.
The new version of the document "sequential gearbox" explains fully how to tune them with this new firmware.
2) RPM sensor signal loss:
Improvement of the resynchronization in case of rpm sensor signal lost.

 

Throttle/RPM : V340 (System V440)
Pressure/RPM : V340 (System V440)

1) Fuel pressure management:
Improvement of calculations for injection time correction in function of the fuel pressure (see documentation 'Fuel pressure management' chapter 'Fuel pressure reference').
- The fuel pressure reference, in case of specific calculations for injection time correction in function of the fuel pressure, is now given in pressure relative to atmospheric pressure and no more in absolute pressure.
- If you import the data from an old Tuneware with which the injection time was corrected by the low fuel pressure (not direct injection management), in this old Tuneware, the fuel pressure reference was given in absolute pressure. So you will have to correct the fuel low pressure reference in the new Tuneware.

 

Throttle/RPM : V330 (System V440)
Pressure/RPM : V330 (System V440)

1) Fly by wire:
- Allows adjusting the detection of a short circuit of the fly by wire.
- Allows the selection between synchronous command mode (standard mode) and asynchronous mode (advised new mode).
The asynchronous mode is preferably to use because
- it allow to manage a more precise position on very small openings, giving a better control of the tick over rpm,
- it consumes less current,
- it makes the electric motor runs cooler,
- it produces less spikes and less noise.
2) Electrical noise:
The interferences filtering on analog inputs have been improved, giving a better stability of the general operation.

 

Throttle/RPM : V320 (System V430)
Pressure/RPM : V320 (System V430)

1) Ignition:
- Allows the use of coil loading time extremely short (<500 microseconds) for very high efficiency coils or capacitive discharges
- Allows a better load of the coils at engine startup
2) Fly by wire:
- Allowed stop of the fly by wire command below a tuneable rpm, to avoid spikes at the engine start with inductive sensors and save power when the engine does not run
- Allowed stop of the fly by wire command if engine stalls, to avoid spikes with inductive sensors and and allow the automatic cutoff of the fuel pump

 

Throttle/RPM : V310 (System V420)
Pressure/RPM : V310 (System V420)

1) Injection:
- Self learning of the injection time base map (needs a professionnal license, or on option for standard licenses)
2) Fly by wire:
- Stop of the fly by wire command allowed below a tuneable rpm, to avoid spikes at the engine start with inductive sensors and save power when the engine does not run
3) Camshaft:
- The main camshaft (engine phase) can be the intake or the exhaust one as well
- Reading of camshafts targets with one missing tooth, one supplementary tooth and regular teeth

 

Throttle/RPM : V300 (System V400)
Pressure/RPM : V300 (System V400)

1) Camshafts:
- Management of proportional positioning of exhaust camshaft
- Reading of camshafts targets with one missing tooth and regular teeth
2) Injection:
- Up to 4 cylinders, management of not phased sequential injection allowed when phase sensor is missing - better than semi sequential injection. Allows to use cylinder by cylinder injection correction maps (see Engine configuration documentation)
- Up to 4 cylinders, semi-sequential injection commands one injector per cylinder, in place of one command for two cylinders previously (warning, the injectors wiring differs from previous versions of semi-sequential injection : it is now the same than the sequential injection one - see installation documentation)
3) Ignition:
- Up to 4 cylinders, management allowed of not phased static ignition when phase sensor is missing - better than twin spark ignition. Allows to use cylinder by cylinder advance correction maps (warning, the coils wiring differs from twin sparks ignition one: see installation documentation)

 

Throttle/RPM : V280 (System V360)
Pressure/RPM : V280 (System V360)

1) Better fault tolerance with CAN-bus sensors WinjNet (including Lambda controller DigiLSU)
- If you use a WinjNet sensor (connected to the ECU by CAN-bus), as for example the Lambda controller DigiLSU, it is mandatory to update your ECU.
- If you also use an injectors driver IMg06 (i.e. gasoline direct injection), this driver also being connected to the ECU by CAN-bus, it is also mandatory to update your driver with a CAN-bus error-tolerant software version (report to drivers dwonloads).
2) Full Display of calculation results of the auxiliary commands.

 

Throttle/RPM : V270 (System V350)
Pressure/RPM : V270 (System V350)

1) Auxiliary CAN-bus works with standard frames (11 bits identifiers) or extended frames (29 bits identifiers), with frame by frame selection.
2) Full display of PID calculations (Results, proportional, derived and integral).
3) Improvement of Lambda sensors fault detection.

 

Throttle/RPM : V260 (System V330)
Pressure/RPM : V260 (System V330)

1) Full management of turbos by turbo rpm or turbo pressure or both with dynamic selection of the management mode.
2) Dynamic management of fuel pressure with rail emptying at deceleration cutoff (see documentation 'Fuel pressure').
3) Advanced detection of speeds measurements errors.
4) Inverted management of on-off auxiliary outputs allowed.

 

Throttle/RPM : V240 (System V300)
Pressure/RPM : V240 (System V300)

1) Improvement of machine internal security and Tunewares security.
2) Improvement of the engine RPM measurement dynamic to get an even more precise following of the accelerations.
3) Modification of the tick over dynamic advance correction : this modification can induce a correction of the tuning of the tick over dynamic advance coefficient compared with the former versions.
- Modification of the average RPM at tick over.
- Adding of mini and maxi tunable limits of dynamic advance correction.
4) Adding of PWM software possibility on auxiliary outputs 4B et 5B.
5) Impovement of electrical spikes withstanding when using motorised throttles.

 

Throttle/RPM : V220 (System V250)
Pressure/RPM : V220 (System V250)

1) Added modification groups that allow to run in multi-maps without using advanced functionalities:
(Allows for example to get several engine tunings selected by a rotactor, but also allows many other applications).
Each modification group allows a specific engine tuning on ignition advance, injection time, richness target and turbo pressure target (if turbo exists).
Selection of the activation condition for each modification group.
See new documentation 'Engine Tuning modification groups'.
2) Modification of the injection time correction by fuel pressure : the correction is done by a differential pressure calculation (see documentation 'Fuel pressure').

 

Throttle/RPM : V210 et V211 (System V250)
Pressure/RPM : V210 et 211 (System V250)

The throttle/RPM software has been modified to V211 version, as a small improvement has been done on injection phase calculation.
The vacuum/RPM software has been modified to V211 version, to fix a bug in the communications with Winjall.
This bug is only seen when using the atmospheric version (and not the turbo one) of the Commander44:
When Winjall is connected to the ECU and if you switch off and on the ECU, Winjall displays a reset request from the ECU, as if a major calibration had been executed, which is not the case.
This bug does not concern at all the engine working, but only the display of the reset request by Winjall.

For the remaining, the V211 version works the same than the V210 version:
1) Repetition of the CAN frames for slow dash boards. This kind of dashboard could not answer to the Commander which then stopped  to send dashboard informations
2) Impovement of the detection and display of the CAN bus errors.
3) Improved management of the sequential gear box.
4) Allows a fast and easy tune of the turbo pressure loop control.
5) Improved bang-bang management.
6) Allows getting the bang-bang from the tick over for canon ball move off.

 

Throttle/RPM : V200 (System V230)
Pressure/RPM : V200 (System V230)

Version 200 is the base version of the new Commander44, Skynam high end ECUs.

 

Top of page


HomeHome